en:tutorials:telemac

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
en:tutorials:telemac [2021/03/18 15:11] – ylecoareren:tutorials:telemac [2022/01/17 11:26] (current) – fzaoui
Line 80: Line 80:
   * Enter in <hi #9BFFFF>**Project name:**</hi>: //'Tuto_TELEMAC'//.   * Enter in <hi #9BFFFF>**Project name:**</hi>: //'Tuto_TELEMAC'//.
   * Choose in <hi #9BFFFF>**Project type:**</hi>: //'physique'//.   * Choose in <hi #9BFFFF>**Project type:**</hi>: //'physique'//.
-  * Click on **[Create Project]**.+  * Click on <hi #47B5E6>**[Create Project]**</hi>.
  
 The project is then created and gives you access to new tabs. The project is then created and gives you access to new tabs.
Line 107: Line 107:
 {{:en:tutorials:tuto_hyd_creation.png?700|}} {{:en:tutorials:tuto_hyd_creation.png?700|}}
  
-  * If this information is valid, you can start the calculation by pressing the **[Create 1 file .hyd]** button.+  * If this information is valid, you can start the calculation by pressing the <hi #47B5E6>**[Create 1 file .hyd]**</hi> button.
  
 Once the process is complete, a file 'd1_to_d9.hyd' is created. Once the process is complete, a file 'd1_to_d9.hyd' is created.
Line 129: Line 129:
 {{:en:tutorials:tuto_sub_creation.png?700|}} {{:en:tutorials:tuto_sub_creation.png?700|}}
  
-  * If the information displayed in this tab is valid, you can start the calculation by pressing the **[Create .sub file]** button.+  * If the information displayed in this tab is valid, you can start the calculation by pressing the <hi #47B5E6>**[Create .sub file]**</hi> button.
  
 Once the process is finished, a file 'sub_PolygonSandreCoarser-dom.sub' is created. Once the process is finished, a file 'sub_PolygonSandreCoarser-dom.sub' is created.
Line 144: Line 144:
 {{:en:tutorials:tuto_hab_creation.png?700|}} {{:en:tutorials:tuto_hab_creation.png?700|}}
  
-  * Then launch the merge with the **[Create .hab file]** button.+  * Then launch the merge with the <hi #47B5E6>**[Create .hab file]**</hi> button.
  
 Once the process is finished, a //'d1_to_d9_sub_PolygonSandreCoarser-dom.hab'// file is created. Once the process is finished, a //'d1_to_d9_sub_PolygonSandreCoarser-dom.hab'// file is created.
Line 155: Line 155:
   * Open the tab <hi #9BFFFF>**Calc. Habitat**</hi> tab.   * Open the tab <hi #9BFFFF>**Calc. Habitat**</hi> tab.
   * Check for <hi #9BFFFF>**Habitat File(s)**</hi> that the //'d1_to_d9_sub_PolygonSandreCoarser-dom.hab'// file is selected.   * Check for <hi #9BFFFF>**Habitat File(s)**</hi> that the //'d1_to_d9_sub_PolygonSandreCoarser-dom.hab'// file is selected.
-  * To add biological models to be calculated, click on the **[Add Models]** button.+  * To add biological models to be calculated, click on the <hi #9BFFFF>**[Add Models]**</hi> button.
  
 This opens the [[en:user_guide:explo_biological_models|biological model explorer]]. This opens the [[en:user_guide:explo_biological_models|biological model explorer]].
Line 169: Line 169:
   * In the second tab <hi #9BFFFF>**Model selection**</hi>:   * In the second tab <hi #9BFFFF>**Model selection**</hi>:
     * Click on the model //'Barbus barbus - adult - BAF01'// in the left-hand list <hi #9BFFFF>**Available models**</hi>.      * Click on the model //'Barbus barbus - adult - BAF01'// in the left-hand list <hi #9BFFFF>**Available models**</hi>. 
-    * (Optional) You can click on **[Show habitat suitability indices]** to display the biological model in an interactive figure+    * (Optional) You can click on <hi #9BFFFF>**[Show habitat suitability indices]**</hi> to display the biological model in an interactive figure
     * Drag and drop from left to right the //'Barbus barbus - adult - BAF01'// model into the right-hand list <hi #9BFFFF>**Selected models**</hi>.     * Drag and drop from left to right the //'Barbus barbus - adult - BAF01'// model into the right-hand list <hi #9BFFFF>**Selected models**</hi>.
  
 {{:en:tutorials:tuto_calc_hab_glisser_dep.png?700|}} {{:en:tutorials:tuto_calc_hab_glisser_dep.png?700|}}
  
-    * Validate with the **[Validate selected models]** button.+    * Validate with the <hi #9BFFFF>**[Validate selected models]**</hi> button.
 The model //'Barbus barbus - adult - BAF01'// has been added to the list of models to be calculated. The model //'Barbus barbus - adult - BAF01'// has been added to the list of models to be calculated.
  
Line 183: Line 183:
 {{:en:tutorials:tuto_calc_hab.png?700|}} {{:en:tutorials:tuto_calc_hab.png?700|}}
  
-  * You can now start the habitat calculation for the adult barbel with the **[Compute habitat]** button.+  * You can now start the habitat calculation for the adult barbel with the <hi #47B5E6>**[Compute habitat]**</hi> button.
  
 Once the process is finished, the result of the model 'BAF01_adult_HV_Dominant' has been added to the file 'd1_to_d9_sub_PolygonSandreCoarser-dom.hab'. By default, at each calculation, the text habitat calculation result file is created: 'd1_to_d9_sub_PolygonSandreCoarser-dom_spu.txt' describing the habitat values and the weighted usable area of adult barbel for each simulated discharge. Once the process is finished, the result of the model 'BAF01_adult_HV_Dominant' has been added to the file 'd1_to_d9_sub_PolygonSandreCoarser-dom.hab'. By default, at each calculation, the text habitat calculation result file is created: 'd1_to_d9_sub_PolygonSandreCoarser-dom_spu.txt' describing the habitat values and the weighted usable area of adult barbel for each simulated discharge.
Line 230: Line 230:
       * <hi #9BFFFF>**mode**</hi>: //'interactive'//.       * <hi #9BFFFF>**mode**</hi>: //'interactive'//.
  
-  * Start the figure creation process with the **[run]** button.+  * Start the figure creation process with the <hi #47B5E6>**[run]**</hi> button.
  
 An interactive habitat map is then displayed. An interactive habitat map is then displayed.
Line 242: Line 242:
   * In this group <hi #9BFFFF>**Figure viewer/exporter**</hi>, choose:   * In this group <hi #9BFFFF>**Figure viewer/exporter**</hi>, choose:
     * <hi #9BFFFF>**tronçon(s)**</hi>: //'Tronçon D'//.      * <hi #9BFFFF>**tronçon(s)**</hi>: //'Tronçon D'//. 
-    * <hi #9BFFFF>**discharge [m<sup>3</sup>/s]**</hi>: all discharges (from //'9.2'// to //'259'//). +    * <hi #9BFFFF>**discharge [m<sup>3</sup>/s]**</hi></hi>: all discharges (from //'9.2'// to //'259'//). 
     * <hi #9BFFFF>**mesh variables**</hi>: //'BAF01_adult_HV_Dominant'//.      * <hi #9BFFFF>**mesh variables**</hi>: //'BAF01_adult_HV_Dominant'//. 
     * Figure options:     * Figure options:
Line 249: Line 249:
       * <hi #9BFFFF>**mode**</hi>: //'interactive'//.       * <hi #9BFFFF>**mode**</hi>: //'interactive'//.
  
-  * Start the figure creation process with the **[run]** button.+  * Start the figure creation process with the <hi #47B5E6>**[run]**</hi> button.
  
 An interactive habitat chronicle is then displayed. An interactive habitat chronicle is then displayed.
Line 271: Line 271:
 {{:en:tutorials:tuto_data_explorer_export.png?700|}} {{:en:tutorials:tuto_data_explorer_export.png?700|}}
  
-  * Start the export process with the **[run]** button.+  * Start the export process with the <hi #47B5E6>**[run]**</hi> button.
  
 At the end of the process, all the requested files have been exported. At the end of the process, all the requested files have been exported.
Line 302: Line 302:
 {{:fr:tutorials:tuto_paraview_stl.png?600|}} {{:fr:tutorials:tuto_paraview_stl.png?600|}}
  
-In a third step, we will look at the exports <hi #9BFFFF>**3D (.pvd, .vtu) Mesh by units**</hi>, namely:+In a third step, we will look at the exports <hi #9BFFFF>**3D (.pvd, .vtu) Mesh units**</hi>, namely:
   * the file 'd1_to_d9_sub_PolygonSandreCoarser-dom_Troncon D_water level.pvd'.    * the file 'd1_to_d9_sub_PolygonSandreCoarser-dom_Troncon D_water level.pvd'. 
   * the 'd1_to_d9_sub_PolygonSandreCoarser-dom_Troncon D_XXXX_water level.vtu' files.   * the 'd1_to_d9_sub_PolygonSandreCoarser-dom_Troncon D_XXXX_water level.vtu' files.
Line 355: Line 355:
   * If necessary, close the <hi #9BFFFF>**Data available**</hi> group.   * If necessary, close the <hi #9BFFFF>**Data available**</hi> group.
   * If necessary, click on the <hi #9BFFFF>**Desired data**</hi> group to open it.   * If necessary, click on the <hi #9BFFFF>**Desired data**</hi> group to open it.
-  * Select the discharge chronicle file //'discharge_chronicle.txt'// with the **[run]** button of the group <hi #9BFFFF>**from .txt file**</hi>.+  * Select the discharge chronicle file //'discharge_chronicle.txt'// with the <hi #47B5E6>**[load and run]**</hi> button of the group <hi #9BFFFF>**from .txt file**</hi>.
  
 {{:en:tutorials:tuto_interp_target.png?700|}} {{:en:tutorials:tuto_interp_target.png?700|}}
Line 368: Line 368:
 {{:en:tutorials:tuto_interp_resultgui.png?700|}} {{:en:tutorials:tuto_interp_resultgui.png?700|}}
  
-  * Click the **[run]** button of <hi #9BFFFF>**View interpolated chronicle:**</hi> to display the interpolated chronicle.+  * Click the <hi #47B5E6>**[run]**</hi> button of <hi #9BFFFF>**View interpolated chronicle:**</hi> to display the interpolated chronicle.
  
 {{:en:tutorials:tuto_interp_chronique_mpl.png?500|}} {{:en:tutorials:tuto_interp_chronique_mpl.png?500|}}
  
  
  • en/tutorials/telemac.1616076688.txt.gz
  • Last modified: 2021/03/18 15:11
  • by ylecoarer