Differences

This shows you the differences between two versions of the page.

--- en:tutorials:telemac [2021/03/18 14:56] – ylecoarer
+++ en:tutorials:telemac [2022/01/17 11:26] () – fzaoui
@@ 80: / 80: @@
   * Enter in <hi #9BFFFF>**Project name:**</hi>: //'Tuto_TELEMAC'//.
   * Choose in <hi #9BFFFF>**Project type:**</hi>: //'physique'//.
-  * Click on **[Create Project]**.
+  * Click on <hi #47B5E6>**[Create Project]**</hi>.
 The project is then created and gives you access to new tabs.
@@ 107: / 107: @@
 {{:en:tutorials:tuto_hyd_creation.png?700|}}
-  * If this information is valid, you can start the calculation by pressing the **[Create 1 file .hyd]** button.
+  * If this information is valid, you can start the calculation by pressing the <hi #47B5E6>**[Create 1 file .hyd]**</hi> button.
 Once the process is complete, a file 'd1_to_d9.hyd' is created.
@@ 122: / 122: @@
     * <hi #9BFFFF>**File (.shp, .gpkg)**</hi>: //'sub_PolygonSandreCoarser-dom.shp'//
     * <hi #9BFFFF>**Classification code:**</hi>: //'Sandre'//
-    * <hi #9BFFFF>**Classification method:**</hi> : //'coarser-dom'//
+    * <hi #9BFFFF>**Classification method:**</hi> : //'coarser-dominant'//
     * <hi #9BFFFF>**Default values**</hi> : //'12, 12'//
     * <hi #9BFFFF>**EPSG code**</hi>: //'2154'//
@@ 129: / 129: @@
 {{:en:tutorials:tuto_sub_creation.png?700|}}
-  * If the information displayed in this tab is valid, you can start the calculation by pressing the **[Create .sub file]** button.
+  * If the information displayed in this tab is valid, you can start the calculation by pressing the <hi #47B5E6>**[Create .sub file]**</hi> button.
 Once the process is finished, a file 'sub_PolygonSandreCoarser-dom.sub' is created.
@@ 137: / 137: @@
 ==== Creating a .hab file ====
-  * Stay in the <hi #9BFFFF>**Substrat**</hi> tab.
+  * Stay in the <hi #9BFFFF>**Substrate**</hi> tab.
   * In the <hi #9BFFFF>**Merging of hydraulics and substrate data**</hi> group, check that the file names are selected for:
     * <hi #9BFFFF>**.hyd filename**</hi>: //'d1_to_d9.hyd'//.
@@ 144: / 144: @@
 {{:en:tutorials:tuto_hab_creation.png?700|}}
-  * Then launch the merge with the **[Create .hab file]** button.
+  * Then launch the merge with the <hi #47B5E6>**[Create .hab file]**</hi> button.
 Once the process is finished, a //'d1_to_d9_sub_PolygonSandreCoarser-dom.hab'// file is created.
@@ 155: / 155: @@
   * Open the tab <hi #9BFFFF>**Calc. Habitat**</hi> tab.
   * Check for <hi #9BFFFF>**Habitat File(s)**</hi> that the //'d1_to_d9_sub_PolygonSandreCoarser-dom.hab'// file is selected.
-  * To add biological models to be calculated, click on the **[Add Models]** button.
+  * To add biological models to be calculated, click on the <hi #9BFFFF>**[Add Models]**</hi> button.
 This opens the [[en:user_guide:explo_biological_models|biological model explorer]].
@@ 161: / 161: @@
   * In the first tab <hi #9BFFFF>**Model filter**</hi>, refine your search by the following criteria:
     * <hi #9BFFFF>**Country**</hi>: //'France'//.
-    * <hi #9BFFFF>**Type of aquatic animal**</hi>: //'fish'//.
+    * <hi #9BFFFF>**Aquatic animal type**</hi>: //'fish'//.
     * <hi #9BFFFF>**Stage and size**</hi>: //'adult'//.
     * <hi #9BFFFF>**Code alternative filter**</hi> : //'BAF'//.
@@ 169: / 169: @@
   * In the second tab <hi #9BFFFF>**Model selection**</hi>:
     * Click on the model //'Barbus barbus - adult - BAF01'// in the left-hand list <hi #9BFFFF>**Available models**</hi>.
-    * (Optional) You can click on **[Show habitat suitability indices]** to display the biological model in an interactive figure
+    * (Optional) You can click on <hi #9BFFFF>**[Show habitat suitability indices]**</hi> to display the biological model in an interactive figure
-    * Drag and drop from left to right the //'Barbus barbus - adult - BAF01'// model into the right-hand list <hi #9BFFFF>**Selected models (0)**</hi>.
+    * Drag and drop from left to right the //'Barbus barbus - adult - BAF01'// model into the right-hand list <hi #9BFFFF>**Selected models**</hi>.
 {{:en:tutorials:tuto_calc_hab_glisser_dep.png?700|}}
-    * Validate with the **[Validate selected models]** button.
+    * Validate with the <hi #9BFFFF>**[Validate selected models]**</hi> button.
 The model //'Barbus barbus - adult - BAF01'// has been added to the list of models to be calculated.
@@ 183: / 183: @@
 {{:en:tutorials:tuto_calc_hab.png?700|}}
-  * You can now start the habitat calculation for the adult barbel with the **[Compute habitat]** button.
+  * You can now start the habitat calculation for the adult barbel with the <hi #47B5E6>**[Compute habitat]**</hi> button.
 Once the process is finished, the result of the model 'BAF01_adult_HV_Dominant' has been added to the file 'd1_to_d9_sub_PolygonSandreCoarser-dom.hab'. By default, at each calculation, the text habitat calculation result file is created: 'd1_to_d9_sub_PolygonSandreCoarser-dom_spu.txt' describing the habitat values and the weighted usable area of adult barbel for each simulated discharge.
@@ 230: / 230: @@
       * <hi #9BFFFF>**mode**</hi>: //'interactive'//.
-  * Start the figure creation process with the **[run]** button.
+  * Start the figure creation process with the <hi #47B5E6>**[run]**</hi> button.
 An interactive habitat map is then displayed.
@@ 242: / 242: @@
   * In this group <hi #9BFFFF>**Figure viewer/exporter**</hi>, choose:
     * <hi #9BFFFF>**tronçon(s)**</hi>: //'Tronçon D'//.
-    * <hi #9BFFFF>**discharge [m<sup>3</sup>/s]**</hi>: all discharges (from //'9.2'// to //'259'//).
+    * <hi #9BFFFF>**discharge [m<sup>3</sup>/s]**</hi></hi>: all discharges (from //'9.2'// to //'259'//).
     * <hi #9BFFFF>**mesh variables**</hi>: //'BAF01_adult_HV_Dominant'//.
     * Figure options:
@@ 249: / 249: @@
       * <hi #9BFFFF>**mode**</hi>: //'interactive'//.
-  * Start the figure creation process with the **[run]** button.
+  * Start the figure creation process with the <hi #47B5E6>**[run]**</hi> button.
 An interactive habitat chronicle is then displayed.
@@ 271: / 271: @@
 {{:en:tutorials:tuto_data_explorer_export.png?700|}}
-  * Start the export process with the **[run]** button.
+  * Start the export process with the <hi #47B5E6>**[run]**</hi> button.
 At the end of the process, all the requested files have been exported.
@@ 302: / 302: @@
 {{:fr:tutorials:tuto_paraview_stl.png?600|}}
-In a third step, we will look at the exports <hi #9BFFFF>**3D (.pvd, .vtu) Mesh by units**</hi>, namely:
+In a third step, we will look at the exports <hi #9BFFFF>**3D (.pvd, .vtu) Mesh units**</hi>, namely:
   * the file 'd1_to_d9_sub_PolygonSandreCoarser-dom_Troncon D_water level.pvd'.
   * the 'd1_to_d9_sub_PolygonSandreCoarser-dom_Troncon D_XXXX_water level.vtu' files.
@@ 355: / 355: @@
   * If necessary, close the <hi #9BFFFF>**Data available**</hi> group.
   * If necessary, click on the <hi #9BFFFF>**Desired data**</hi> group to open it.
-  * Select the discharge chronicle file //'discharge_chronicle.txt'// with the **[run]** button of the group <hi #9BFFFF>**from .txt file**</hi>.
+  * Select the discharge chronicle file //'discharge_chronicle.txt'// with the <hi #47B5E6>**[load and run]**</hi> button of the group <hi #9BFFFF>**from .txt file**</hi>.
 {{:en:tutorials:tuto_interp_target.png?700|}}
@@ 368: / 368: @@
 {{:en:tutorials:tuto_interp_resultgui.png?700|}}
-  * Click the **[run]** button of <hi #9BFFFF>**View interpolated chronicle:**</hi> to display the interpolated chronicle.
+  * Click the <hi #47B5E6>**[run]**</hi> button of <hi #9BFFFF>**View interpolated chronicle:**</hi> to display the interpolated chronicle.
 {{:en:tutorials:tuto_interp_chronique_mpl.png?500|}}